Clean & Care Instructions

Avoid Abrasive cleaners such as: dry powders, acids, graffiti cleaner, steel wool and
scrubbing pads as these may cause dulling to finishes, reactions with plastics, and scratch marks. Using the incorrect cleaner or cloth can result in marring of the plexi or fabric.

Plexi: Always soft, non-abrasive cloth (not paper towel unless it is soft, not textured). Cleaners tested on the product have been Clorox wipes, Hand Sanitizer (with Isopropyl Alcohol (70%) or Hydrogen Peroxide) and wiped clean with the non-abrasive cloth as
mentioned before to remove excess product.

PET (Polyethylene terephthalate):
Recommended Cleaning Solutions
• 50/50 solution of warm water and bleach (5.25% sodium hypochlorite solution)
• 3% Hydrogen peroxide
• Distilled water (for stain removal only)

Recommended Cleaning Steps
• Apply appropriate cleaning solution (see recommended cleaning solutions above) to a piece of white, lint free cloth. Use a hand spray applicator, do not oversoak.
• If required, renew the cleaning cloth. Repeat process until there is no further transfer of the dirt to the cloth
• Use a clean cloth or sponge soaked in water to remove any residue.
• Allow treated surface to air dry

** Cleaning information is offered for general guidance and is not a guarantee. The use of certain cleaning agents can be harmful to the surface appearance and lifespan of a product. Gateway Office assumes no responsibility for damage to a product resulting from lack of cleaning, improper cleaning or the misuse of cleaning agents. Certain clothing and accessory dyes (such as those used on denim jeans) may migrate to materials and cause permanent damage. Gateway Office cannot be held responsible for dye transfer caused by
external contaminants.

Your decision to purchase Gateway Laminate products will bring you years of quality performance. Everyday cleaning of our products is as simple as a quick wipe with a damp sponge. All resist muddy fingerprints, coffee spills and so much more. Be sure to read and follow the recommended care and cleaning procedures.

Routine Care

To clean the surface, use a damp cloth or sponge and a mild soap or detergent. Rinse thoroughly with warm water and wipe dry.

Difficult stains such as coffee or tea can be removed using a mild household Cleaner/detergent and a soft bristled brush, repeating as necessary.

If a stain persists, use a paste of baking soda and water and apply with a soft bristled brush. Light scrubbing for 10 to 20 strokes should remove most stains. Although baking soda is a low abrasive, excessive scrubbing or exerting too much force could damage the decorative surface, especially if it has a gloss finish.

Stubborn stains that resist any of the above

cleaning methods may require the use of undiluted household bleach or nail polish remover. Apply the bleach or nail polish remover to the stain and let stand no longer than two minutes. Rinse thoroughly with warm water and wipe dry. This step may be repeated if the stain appears to be going away and the color of the laminate has not been affected. WARNING: Prolonged exposure of the laminate surface to bleach will cause discoloration.

Hot pans and heat-producing appliances (such as

electric skillets), when set directly upon countertops, can mar the product’s beauty. Always use a heat shield, hot pad or trivet.

A Few Notes of Caution

  • Acidic or abrasive cleaners can damage laminate surfaces; do not use them.
  • Drain cleaners containing lye will permanently

damage any Gateway Products Laminate surfaces. If you spill a drain cleaner, wipe it up immediately and rinse several times with water.

Hair, textile, and food dyes can cause permanent stains. If dye should happen to spill, wipe it up immediately with dishwashing detergent or an all-purpose cleaner.

Never place pots or dishes directly from the oven or burner on an unprotected laminate surface; such extreme heat can cause cracking or blistering.

Do not work with oven cleaners on an unprotected countertop. Wipe spills away promptly and rinse several times with water.

Rust removers contain harsh chemicals which will quickly cause permanent damage. If a spill occurs, wipe off all residue immediately, wash thoroughly with soapy water and rinse several times.

Steel wool and other abrasive pads will damage Wilsonart Laminate. Don’t use them for cleaning and don’t store steel wool pads on your countertop; the metal can rust and leave stains.

Toilet bowl cleaners contain harsh chemicals that can cause permanent damage. If spills occur, wipe up immediately, wash the surface with soapy water and rinse several times.

Recommended HouseHold cleaners


Glass Plus®


Mr. Clean®

Formula 409®

Isopropyl Alchol (Isopropanol)

*Prolonged exposure to bleach will cause discoloration.

When cleaning Gateway Products Laminate, DO NOT use products that contain the following ingredients:

Hydrochloric Acid (Muriatic Acid, Hydrogen Chloride)

Sulfuric Acid (Oleic Acid, Oil of Vitriol, Oleum)

Hydrofluoric Acid (Rust Remover)

Phosphoric Acid (Rust Remover)

Sodium Hydroxide (Caustic Soda, Caustic Lye, Soda Lye)

Pumice (abrasive)